Barska AU11408 GLX Green Laser w/Built-In Mount and Rail Bedienungsanleitung PDF herunterladen

Handgun Mounting

WARNING: BE CERTAIN THAT YOUR FIREARM IS NOT LOADED AND POINTED

AWAY FROM YOU IN A SAFE DIRECTION

ATTENTION: THIS BARSKA LASER SIGHT IS A POWERFUL TARGETING DEVICE

THAT REQUIRES SPECIAL ATTENTION WHEN OPERATING. CAREFULLY READ

THE FOLLOWING INSTRUCTIONS AND SAFETY PRECAUTIONS BEFORE USING

THIS PRODUCT.

CAUTION: UNAUTHORIZED USE MODIFICATIONS OF ADJUSTMENTS OR PERFORMANCE OF

PROCEDURE OTHER THAN SPECIFIED HEREIN MAY RESULT IN DANGEROUS/HAZARDOUS

RADIATION EXPOSURE.

LASER LIGHT: AVOID DIRECT EYE EXPOSURE.

WARNING KEEP OUT OF REACH OF CHILDREN.

DO NOT POINT LASER AT PEOPLE, PETS, SHINY/HIGHLY REFLECTIVE SURFACES,

AIRPLANES OR ANY OTHER OBJECT NOT INTENDED FOR DESIGNATED USE.

Handgun Mounting:

1. Use included allen wrench to remove the side of the rail mount by

unscrewing the two screws on the side of the compact mount. Remove the

stabilizing cross bar from inner channel, use cross bar if needed by

inserting into rail channel.

2. Slide laser sight on to hand guns lower frame rail.

3. Replace side of mount on to laser and gun rail insert the two mounting

screws and tighten with allen wrench.

Rifle Rail Mounting:

1. Use included allen wrench to remove the side of the rail mount by

unscrewing the two screws on the side of the compact mount. Remove the

stabilizing cross bar from inner channel, use cross bar if needed by

inserting into rail channel.

2. Slide laser sight on to rifles weaver / piccitanny rail. Ideally on rifles

bottom rail.

3. Replace side of mount on to laser and gun rail. Insert the two mounting

screws and tighten with allen wrench.

Zeroing Windage and Elevation Adjustment:

1. At the front side and bottom of laser there are adjustment screws for the

laser’s windage and elevation. (See item #2) Use the included allen wrench

to turn the adjustments screws clockwise or counter clockwise. The

bottom screw will move the laser dot up or down and the side screw will

move the dot from side to side.

2. Using the windage and elevation adjustments zero the laser dot in at the

set distance you will be targeting. When changing shooting distance you

will need to reset the elevation (Reset both W/E if laser is side mounted).

Attaching Cable Switch:

To bypass the slide switch and use the included cable switch you will need to

remove the cover at the back of the laser, use a coin to unscrew the cover.

Then screw the cable switch into the back of the laser.

Replacing Battery:

Unscrew the front laser head to insert new battery, replace laser head and

tighten.

Product parts:

1. Laser diode head

2. Windage and elevation adjustment

3. CR123A battery

4. Compact weaver / picitanny mount with removable

stabilizing cross bar. That can be attached to a

hand guns lower frame rail, rifles weaver/piccitiny

rail, or in combination with Barska multi-rail scopes

5. Weaver / Picitanny accessory rail

6. Slide switch

7. Back cover

8. Cable switch

9. Two side mounting screws

10. Side rail mount

11. Stabilizing cross bar

Note: When mounting laser sight, place weapons safety on and unload all

ammunition from the firearm. When mounting laser to weapon keep the laser in

off position to avoid exposure to eyes.

BC150

La Verne, CA 91750, USA

www.barska.com

<5mW

532(±10)nm

1000 YDS

Windage / Elevation

CR-123A 1

Tecnical Data:

Output Power

Wavelength

Max Reach Capacity

Adjustments

Battery Type

02/10

BC-118

GREEN LASER SIGHT

1 YEAR LIMITED WARRANTY

BARSKA® Optics, as manufacturer, warrants this new precision optical product to be free of original

defects in materials and/or workmanship for the length of time specified by this warranty. This

warranty does not include damage caused by abuse, improper handling, installation, maintenance,

normal wear-and-tear, unauthorized repairs or modifications and tampering in anyway.

This warranty is limited to the original purchaser and is not transferable. This warranty applies only to

products purchased in the United States of America and Canada.

In the event of a defect within 30 days, the consumer must return the defective unit to the BARSKA

dealer (the place of purchase) at his/her own expense.

Beyond 30 days, BARSKA products should be sent to the following address for warranty repairs.

Products must be packed carefully and sturdily to prevent damage in transit, and returned freight

prepaid to:

BARSKA

1721 WRIGHT AVE.

LA VERNE, CA 91750

For additional and updated information

please visit our website at www.barska.com

Please email [email protected] or call 1-888-666-6769 for Return Merchandise Number (RMA#) before

any returns.

NOTE: All merchandise received without a valid RMA # will be returned to shipper at his/her own

expense.

Please include all of the following when returning BARSKA products for service and/or replacement:

1. Please write your complete details (Name, Address, Telephone #, E-mail address, RMA#, etc.)

2. Purchase receipt or Proof of Purchase. (Original/Copy)

3. A brief explanation of the defect.

4. A Check/Money Order of $20.00 to cover inspection, shipping and handling.

*Please allow 6-8 weeks for delivery.

This product will either be replaced or repaired at the discretion of the warrantor. If it's a discontinued

item, we will replace the product with an equivalent product. Should the repair not be covered by this

warranty, an estimate will be sent for your approval. Non-warranty repairs or refurbishing of your

optical products are always provided at a reasonable cost.

BARSKA® Optics shall not be liable for any consequential, incidental and/or contingent damages

whatsoever. This warranty supersedes all previous BARSKA® Optics warranties.

Rifle Rail Mounting

1 YEAR LIMITED WARRANTY 1

Inhaltsverzeichnis

Seite 1 - 1 YEAR LIMITED WARRANTY

Handgun MountingWARNING: BE CERTAIN THAT YOUR FIREARM IS NOT LOADED AND POINTED AWAY FROM YOU IN A SAFE DIRECTIONATTENTION: THIS BARSKA LASER SIGHT I

Kommentare zu diesen Handbüchern

Keine Kommentare

Barska AU11408 GLX Green Laser w/Built-In Mount and Rail Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Optische Geräte Barska AU11408 GLX Green Laser w/Built-In Mount and Rail herunter. BARSKA AU11408 GLX Green Laser w/Built-In Mount and Rail User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Optische Geräte Barska AU11408 GLX Green Laser w/Built-In Mount and Rail